Issues

• CC2C COSMOS 26.10.1 — Intermittent Load-Cell Probing Failures

  OpenCentauri/cosmos#477 · Filter by author serghut opened on Nov 13, 2026
  1

• Elegoo Centauri Carbon – Load Cell Probing Failures and Possible Tap Analysis Issue

  OpenCentauri/cosmos#476 · Filter by author HashemMD opened on Nov 12, 2026

• Cannot switched to OC patched 26.10.1

  OpenCentauri/cosmos#474 · Filter by author dmeridith opened on Nov 8, 2026
  22

• File browser defaults to config instead of gcodes

  OpenCentauri/cosmos#473 · Filter by author gms004a opened on Nov 8, 2026
  1

• CC1 : Klipper crashed mid print

  OpenCentauri/cosmos#472 · Filter by author snazy2000 opened on Nov 7, 2026
  3

• AFC tool-change restoration movement returning back to print with layer shifting

  OpenCentauri/cosmos#471 · Filter by author Demon1019 opened on Nov 5, 2026
  2

• CANVAS/AFC: fill vendor_name and name in lane_data (from RFID tag, or manual entry)

  OpenCentauri/cosmos#468 · Filter by author Surfoo opened on Nov 3, 2026
  3

• CC2: BED_MESH_CALIBRATE moved position_endstop by 0.2 mm (first layer then too high)

  OpenCentauri/cosmos#462 · Filter by author BorjaLL opened on Nov 1, 2026

• CC2: how to revert from Cosmos to stock Elegoo firmware (A/B slot, toolhead/bed MCU)

  OpenCentauri/cosmos#460 · Filter by author BorjaLL opened on Nov 1, 2026
  26

• Load Cell Probe Error: current absolute force of "-18385.5g" exceeds force_safety_limit (+/-3000.0g) before probing! during initial calibration: bed leveling

  OpenCentauri/cosmos#456 · Filter by author JohnDS1 opened on Oct 31, 2026
  5

• mjpegstreamer breaks webcam ui in mainsail on safari

  OpenCentauri/cosmos#433 · Filter by author mmerickel opened on Oct 24, 2026
  3

• skew profile enablement can send printhead out of bounds

  OpenCentauri/cosmos#429 · Filter by author bniggemyer opened on Oct 22, 2026

• Webcam FOV / Resolution

  OpenCentauri/cosmos#422 · Filter by author peepsnet opened on Oct 17, 2026
  3

• Timelapses

  OpenCentauri/cosmos#420 · Filter by author WaveGu1de opened on Oct 16, 2026
  5

• AFC tool-change restoration movement can collide with the purge-tray lever

  OpenCentauri/cosmos#399 · Filter by author Vampiro1 opened on Oct 10, 2026
  3

• CC1 + CANVAS: underextrusion with default extruder run_current 0.7 A, fixed by 0.8 A (stock value)

  OpenCentauri/cosmos#387 · Filter by author iDomi94 opened on Oct 7, 2026

• Adaptive bed meshing vs default

  OpenCentauri/cosmos#375 · Filter by author Notjohnsnow opened on Oct 2, 2026
  1

• CANVAS tool load timed out

  OpenCentauri/cosmos#369 · Filter by author maxpajewski opened on Sep 30, 2026
  7

• MCU shutdown "Timer too close" when M106 P3 (case_fan) is sent right after "calculate extruder phase offset"

  OpenCentauri/cosmos#366 · Filter by author DaniHem opened on Sep 28, 2026
  2

• RESUME fails with "Extrude below minimum temp" when PRINT_START was not used

  OpenCentauri/cosmos#324 · Filter by author Tanguille opened on Sep 11, 2026

• Support DHCP Option 42 (NTP Servers) for Chrony

  OpenCentauri/cosmos#268 · Filter by author rodripr1 opened on Jul 23, 2026

• [CC1] RTL8821CU rtw88 post-bind USB control transfers fail with -EPROTO

  OpenCentauri/cosmos#264 · Filter by author pdscomp opened on Jul 21, 2026

• [CC1] RTL8821CU fails USB enumeration with -EPROTO after warm reboot

  OpenCentauri/cosmos#263 · Filter by author pdscomp opened on Jul 21, 2026

• occasional 'timer too close' during printing

  OpenCentauri/cosmos#246 · Filter by author vytrixGH opened on Jul 14, 2026
  10

• Separate macros for PID tuning and Input Shaping

  OpenCentauri/cosmos#102 · Filter by author RowanSkie opened on Apr 7, 2026
  1