Repository navigation
Conversation
LM20MeshNode rev 0.1 (https://github.com/cvaldess/LM20MeshNode): a Minew ME54BS13 module (nRF54LM20A, 32.768 kHz crystal on board) with an EBYTE E22-900MM22S on SPIM22 (P1.15-P1.18), an EBYTE E108-GN04S on UARTE20 as Serial1 (P1.03/P1.29), an nPM1300 and the board's sensors and OLED on TWIM30 (P0.03/P0.04), three buttons and one status LED (P2.00). Same identity pin map as the nRF54LM20-DK. A board of its own, rather than reusing nrf54lm20dk, also makes the PlatformIO builder pick release/lm20meshnode_bootloader.hex for it.
cvaldess
added a commit
to cvaldess/LM20MeshNode
that referenced
this pull request
Nov 13, 2026
The lm20meshnode variant is open as a draft: meshtastic/firmware#12354 (on top of the nRF54LM20-DK support in #12130), with the core variant (andyshinn/nRF54_Arduino#3) and the bootloader board (andyshinn/nRF54_Bootloader#3). Status line updated, and a new section on what the variant does on this board (nPM1300 setup, buttons, bootloader buttons, USB) and what is still untested. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
Adds
variants/lm20meshnodefor the LM20MeshNode, an open hardware Meshtastic pocket node built around the nRF54LM20A. Design files (KiCad, CERN-OHL-S v2): https://github.com/cvaldess/LM20MeshNodeUSE_LFXO)Serial1(UARTE20): TX P1.03, RX P1.29Same identity pin map as the nRF54LM20-DK variant in #1. The PR only adds these two files, so it builds without #1 or #2, but the board uses the native USB port (#2), and its SPIM22 on P1 relies on the prescaler fix in #1.
A variant of its own, rather than reusing
nrf54lm20dk, also makes the PlatformIO builder pickrelease/lm20meshnode_bootloader.hex(the bootloader board is andyshinn/nRF54_Bootloader#3).The pins follow the rev 0.1 schematic, checked against its netlist. Tested: the Meshtastic firmware for the board builds against this variant on top of #1 and #2 (cvaldess/nRF54_Arduino
39d1fbf). The board has not been manufactured yet, so nothing has run on hardware.Meshtastic variant for the board: meshtastic/firmware#12354 (draft).